Floor receive
The receiver’s screen (/floor/receive/:id): book a delivery in by scanning. The office can book the same receipt at the desk, with Receive on a line in Receiving. Both write the same receipt.
On this page
Section titled “On this page”- The loop
- Lots and serial numbers
- Putaway: in the same pass, or later
- Over-receipt and capacity
- Finishing the receipt
- See also
The loop
Section titled “The loop”- Scan the item — identifies what arrived.
- Confirm the quantity — how many of it.
- Scan the putaway bin — where it is going.
Repeat until the delivery is booked in. The receipt moves from Expected to Being received on the first line and to Received when it is complete.
Where the warehouse sends units for waiting orders straight to packing, the screen says so instead of a bin: Take 3 to packing for #1001. Straight to packing explains the switch.
Where the warehouse receives to a dock, step 3 is a single press instead: Accept 24 books the units into the dock, and the screen says where they go next (“Goes to DOCK-01 · Put away later”, or “Inspect next”). Without a scanner, Receive this on a line under Still expected starts it, where the warehouse allows tapping.
Lots and serial numbers
Section titled “Lots and serial numbers”- A lot-tracked item always asks for its Lot number. Where the item tracks a date, it asks for that too, in the item’s own words, such as Best before or Use by; a lot whose date is required cannot be booked without it.
- A serial-tracked item whose serial numbers are recorded at receiving asks for every unit: Scan each unit, one serial number per unit, listed as you go. (An item set to record them at packing asks at the pack station instead.) A serial already in stock, shipped or belonging to another item is refused with the reason. In a warehouse set to Scan only, typing serial numbers instead of scanning them needs a lead’s approval.
- A partial carton of serial units: a lead can Accept 6 now for the units scanned so far.
See Lots & serial numbers for how the office reads them later.
Putaway: in the same pass, or later
Section titled “Putaway: in the same pass, or later”With the warehouse’s receiving policy Straight to a shelf, confirming the bin in the same loop means putawayPutawayMoving received goods from the receiving area to the bin they belong in. With the receiving policy **Straight to a shelf** it happens during receiving; with a dock policy a putaway task follows the receipt (after the inspection, where the policy inspects). A work order's finished goods that Floormode books onto the workbench bin `WO-STAGE-01` get a putaway task too; an output that needs the receiver (serial numbers, or a date Floormode cannot work out) is received on its receipt instead.Read more → happens as goods are received. With At the dock, shelved later the goods are booked into DOCK-01 and a putaway task follows; with Check goods first (inspection) they are booked into QC-IN-01, inspected, and the passed units get a putaway task. The policy is set per warehouse (Receiving lists all three).
Where Placement is configured, the screen proposes the home bin rather than making the receiver decide.
Over-receipt and capacity
Section titled “Over-receipt and capacity”Two guards apply as you confirm quantities:
- Over-receipt tolerance — a per-warehouse policy for how much more than expected the floor may book in before the app pushes back.
- Capacity warnings — where the destination location has a capacity set, putaway warns if the delivery will not fit. A location with no capacity set is treated as unlimited, never as zero.
Anything received that does not match expectations becomes a discrepancyDiscrepancyAny difference between what the system expected and what was physically found — on a receipt, at a bin during picking, or in a count.Read more → on the receipt, visible to the office rather than absorbed silently.
Finishing the receipt
Section titled “Finishing the receipt”⋯ → Finish receipt closes it. With every line received it says so; with lines still open it asks first, and finishing closes them short. A line whose product is not in your catalogue yet cannot be scanned: Close them short records it as not received, Keep open, tell the office leaves the receipt open for the office to add the product.
See also
Section titled “See also”- Receiving — the office view and receipt statuses.
- Placement — the rules behind the proposed bin.
- Item dimensions & capacity — where capacity warnings come from.
- Wallboard, work area & inspect — passing and rejecting goods received into inspection.
- Floor move — the putaway that follows a dock receipt.